ABSTRACT The practical importance of a battery charger in today world cannot be over emphasized. This is so as those batteries accumulators are immensely needed by out auto mobile and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery charger. However the procedure fro developed cover the construction of battery charger for battery sizes ranging from 6 voltage to 24volatge (heavy duty) batteries. The prototype of a batter...
ABSTRACT This project, 12v battery charge consist of few chapters, deal extensively with the design and construction of a batter charge which is capable of charging a 12v battery. The introductory chapter goes a long why in defining the battery charger and explanations of the mode of operations will be death with as we proceed. TABLE OF CONTENT Construction of a 12v Battery Charger Approval Dedication Acknowledgement Abstract CHAPTER ONE 1.1 Introduction CHAPTER TWO ...
ABSTRACT The battery which has always serve as a sources of electrical current has in the past been invalid and inmost cases seen as monument after implicating as battery wound have to be brought over and over again the implicating has been that of lot of money is been spent for this purpose we give appraise for the advancement of technology which today had led to the production of battery which could be made functional after it energy may be used up this has been made possible by rechargin...
ABSTRACT The construction of a 3-phase motor operation indicator exposes the techniques and skills employed in the construction of complex electrical circuit. The combination of contactors overload relay and other component to achieved the desired goal is diagrammatically and descriptively treated of practical knowledge TABLE OF CONTENTS Title page Approval page Dedication Acknowledgement Abstract Table of contents CHAPTER ONE 1.0Introduction 1.1Background 1.2Aim and obje...
ABSTRACT Audio loudspeaker (output transducer) is on of the most essential and powerful device used in telecommunication system. This is device capable of converting electrical signal into sound and vice versa. It is made up of few time of non-magnetic wire wound on a light cylindrical former that is mounted so that it can move freely insides the magnetic field of a strong permanent magnet. The speaker cone it attached to the voice coil and attached with a flexible mounting to outer ting of...
ABSTRACT This project is concerned with the fabrication of as a single face pressurized kerosene cooker. The report shows the possible way in which the above mentioned can be designed, fabricated and maintained. Its also shows the strength and properties of the materials it is made of. Defects of the equipment can come through inability to maintain and inability to use well. It can be due to irregular cleaning of pressurized parts, exposure to rain, moisture and sunlight as well as i...
ABSTRACT This work on the construction and fabrication of a mobile deep freezer revolves around the concept of refrigeration. The concept of refrigeration revolves around the reverse Carnot cycle. This is a cycle involving isentropic expansion (at the throttling valve), isothermal expansion (at the evaporator), isentropic compression (at the compressor) and isothermal compressor ( at the condenser) Compression raises the temperatures of the refrigerant above that of its natural surrounding...
ABSTRACT Mechanical Engineering Department of the named Institute has many non – operational malhiues. Sequel to the fact, maintenance was poorly excuted which resulted to the breakdown deep freezer. Quality and effectiveness of machine maintenance were well observed. Also, a minimized maintenance and a highly successful repair was adopted. In other words during the repair and rehabilitation of the facility Deep Freezer, appropriate tools, cost and quality of materials were well...
ABSTRACT Books are used recoding of what is happening or event that has already taken place which can be storing information it is useful and for the information that such books contained not to cost it support to be properly kept and these can be done when those books are kept in a cool dry place and a place free from rodents and insects attacked Therefore, our contribution to proper storage of books is the deigns and construction of a metallic bookshelf that will be economically cheap an...
ABSTRACT This work is an attempt evolve a quicker and easier method of achieving Transportation. This will no doubt save considering human labour and time wasted involved in traditional manual method of transportation. To achieve this, preliminary experiment was first carried out to determine the optimum speed of the motor vehicle. Various design alternative s for achieving the design solution were sythesized and a choice of an economic method which would satisfy the objective was made. Base...
ABSTRACT This project was Carrie lent using sub-bituminous coal and crude palm oil. The degree of bleaching of the palm oil was monitored with a spectorphoto meter. The coal was collected in a lump from the mine. It air-chiecl to removed the moisture content and thereafter, size reduced to a small particle size foe effective activation. The activation process was carried out in a fume cup board and phosphoric acid was used as an activated agent. In the treatment of palm oil, sodiu...
ABSTRACT Water Purification Unit or filtration unit is designed in way that it will give a nice result. Like in our filtration, we have sand and carbon filter that were responded to separate the suspended solid particles, odour and taste of the water, which will give a very nice filtered water at the end of the filtration. This unit has no chemical engineering operation, but a physical separation process that will separate the dead micro organisms and the task, colour odor of the water. ...
ABSTRACT The major aim of this project research work is to produce emulsion paint from locally sourced pigment & extenders. The materials used for the production was of local source. The major raw materials used for the production of the emulsion paint: water, titanium iv oxide, calcium carbonate, kaoline, calgon, natrosol, biocide P.V.A, ammonia, deformer (Ginap) kerosene, yellow iron oxide and red iron oxide. Emulsion paint of two (2) samples was produced, and calcium carbonate locally obt...
ABSTRACT The refurbishment of the fluid flow demonstration unit was carried out in the Chemical Engineering pilot plant laboratory of the Institute of Management and Technology Enugu. The refurbishment process was carried out to ensure adequate functioning of the unit, to allow the continuous use of equipment in the pilot plant, so that student would use it in understanding the nature of the flow of fluid through pipe lines, these process was also for the development of the knowledge of ever...
ABSTRACT The construction of the five (5) litre Electric Kettle was carried out in mechanical workshop of the Institute of Management and Technology Enugu. (I.M.T). The fabrication process, included measuring and marking out operations of which the following dimensions was taken; the cylindrical body was taken as 170mm by 700mm in height and length respectively, the base diameter was 223mm, the lid diameter 140mm, length of nozzle 75min, water outlet and inlet were 20mm and 35mm, respectivel...