CHAPTER ONE INTRODUCTION 1.1 BACKGROUND OF STUDY Buckling analysis of isotropic rectangular plate has been a subject of study in solid structural mechanics for more than a century. Many exact solutions for isotopic plates have been developed. Steel rectangular plates are widely used in buildings, bridges, automobiles, and ships. Rectangular plate has width size comparable to size of their lengths and so is modeled as two - dimensional plane members unlike beams and columns. Under compress...
ABSTRACT This research work presents Nonlinear Analysis of Isotropic Thin Rectangular Plates using Energy Principle (Ritz method). Isotropic thin Rectangular plate having different twelve boundary conditions were analyzed and these boundary conditions were formed by combination of three major supports – Clamp, C; Simply supported, S; and Free, F. With this combination, the twelve boundary conditions analyzed include: SSSS, CCCC, CSCS, CSSS, CCSS, CCCS, CCFC, SSFS, CCFS, SCFC, CSFS, and...
ABSTRACT Powdered Cassia Siamea leaves were investigated as a possible corrosion inhibitor for mild steel in 2 M HCl. Terephthal amide obtained from depolymerizing waste PET (Polyethylene terephthalate) bottles through aminolysis using mono ethanol amine (MEA), served as an additive to improve the efficiency of the powdered leaves. The plant inhibitor was prepared by dissolving 1.5 g of the powdered leaves in 300 ml of 2 M HCl and boiled for 3 hours. Corrosion rates of the steel samples were ...
ABSTRACT Sugarcane as an agricultural product is a readily available source of food for its sugar content. However, Sugarcane Bagasse Ash (SCBA) is the bi- product formed at sugar industries from the burning of sugarcane after the sugar content has been extracted. Sugarcane Bagasse Ash (SCBA) is a fibrous waste product containing mainly aluminum and silica, calcium ions to produce calcium aluminate hydrate (CAH) and calcium silicate hydrate (CSH) shown in the pozzolanic reaction below. Ca2+ +...
Abstract A simulation study of the effect of shear stresses in non-reinforced and reinforced structures was carried in this work. Using the Finite Element Method and equations of elasticity, columns and concrete deck of a simple storey structure were subjected to plane strain conditions. The results showed that proper reinforcement causes stresses to be directed into the reinforcements with the resultant shear stresses in the steel reinforcements far below the yield stresses of the steels. In...
This report is in four sections Research Work & Research Assistantship at Imperial College of Science, Medicine & Technology, LondonTeaching and Administrative Experience in University of IbadanTeaching and Administrative Experience outside University of IbadanMajor Conferences/Workshop attended
ABSTRACT Nigeria is the highest producer of cassava in the world and cassava juice is rich in hydrocyanic acid, a by-product from the extraction process.
ABSTRACT The critical energy situation in Nigeria suggests the need to study energy and exergy utilization in households, with the aim of pinpointing areas of waste and suggesting alternative measures for effective and efficient utilization of scarce resource.
ABSTRACT Failure in pre-cast waffle slabs can be attributed to factors like analytical error, poor handling during transportation and placement which factors often lead to partial/total failure of slabs. The conventional method of analysing waffle slabs focuses on the ribs, while the slab portions at the top are avoided. This has led to under reinforcement and subsequent failure of the slab portions that are usually in direct contact with loads. In this study, a method that incorporates both...
ABSTRACT A considerable fraction of sand in Niger Delta Area of Nigeria is contaminated with crude oil. The contaminated sand is largely utilised by local contractors for the production of concrete. However, there is need to establish its suitability in concreting. Previous works have centered on hardened uncontaminated concrete in crude oil environment but not on concrete made with Crude Oil Contaminated Sand (COCS). This research was designed to evaluate the effect of COCS on some engineer...
Air-conditioning system design and ducting analysis has over the years been an aspect of Engineering, which even though has developed greatly, yet it brings about very tedious tasks of analysis, low level of accuracy, and a lot of time input in carrying out its analysis manually. This work makes provision for the use of a software package, designed for ducting analysis. It has tile capability of handling analysis for buildings having as much as nine (9) floors, with each floor having up to tw...
ABSTRACT Failure in pre-cast waffle slabs can be attributed to factors like analytical error, poor handling during transportation and placement which factors often lead to partial/total failure of slabs. The conventional method of analysing waffle slabs focuses on the ribs, while the slab portions at the top are avoided. This has led to under reinforcement and subsequent failure of the slab portions that are usually in direct contact with loads. In this study, a method that incorporates bot...
ABSTRACT Environmental exposure to lead, a highly toxic heavy metal, is a significant cause of human morbidity and mortality. However, the determination of lead levels in homes and built environment have not been well investigated in Nigeria. This study was designed to evaluate the lead levels in dust, paint, paint chips, soil and water; and to ascertain the geotechnical properties of soil in the home environment in Ibadan. Four Focus Group Discussions (FGDs) were conducted and six hundred ...
ABSTRACT This paper presents the evaluation of the impact of climate change on water resources and yield capacity of Asa and Kampe reservoirs. Trend analysis of mean temperature, runoff, rainfall and evapotranspiration was carried out using Mann Kendall and Sen’s slope, while runoff was modeled as a function of temperature, rainfall and evapotranspiration using Artificial Neural Networks (ANN). Rainfall and runoff exhibited positive trends at the two dam sites and their upstream while fore...
ABSTRACT Experiments have been conducted to develop temper-annealing schedule for continously cast and cold-worked aluminium 1200. By using the method of graphical combination of the results of tensile and deep drawn tests, it is shown that a cost effective temper-annealing schedule that would impart improved mechanical properties.