ABSTRACTThe 200W solar system was determined by load assessment, solar panel number determination, battery requirement and then inverter sizing. A complete solar panel rated at 200w was however purchased, together with 2 no. 150A solar battery, 1500W inverter and also 10A charge controller. These were assembled together with necessary protective gadgets like cut out switches; to give the 200W expected. The solar panel was mounted outside the building to allow for maximum collection of sun ene...
ABSTRACTThe design and construction of a 60A, 3-Ф automatic power changeover from public utility supply to generator and vice versa was aimed at providing a useful system for use in our homes or offices. The system was achieved with a 66A 3-Ф contactor, 100mA transformers and relays. The system turns on a generator when the public utility (PHCN) is off by cranking the starter and a provision was made to stop cranking when the generator is fully started. A delay was provided to stop the gene...
Abstract A wireless signal jammer is a device which blocks transmission by creating interference. This wireless signal jammer can be categorized into the Radio Frequency (RF) jammer and GSM jammer.A Radio Frequency jammer is a device used to disrupt or prevent communication via a broadcasted RF signal. It is an RF and GSM frequency disrupter commonly known as wideband radio frequency (RF) and GSM cell phone jammer. Simultaneously, they can blocks all commercial FM broadcast band (87.5 MHz to ...
ABSTRACTAutomatic water level controller for both overhead and underground tank is designed to monitor the level of water in a tank. It displays the level of water and when it is at the lowest level; a pump is activated automatically to refill the tank. When the tank is filled to its maximum capacity, the pump is automatically de-energized. Several circuits are put together to ensure proper working of this design, and the block diagram includes the supply unit, the micro-processor unit, the s...
ABSTRACTT-junction traffic light controller is such a device that will play a significant role in controlling traffic at junctions, to ease the expected increased rush at such junctions and reduce to minimum disorderliness that may arise, as well as allowing the pedestrians a right of the way at intervals rather than being struck down when in a hurry to cross the roads. Such an electrical system with a touch of electronics that control the flow of traffic in a pre-determined sequential patter...
ABSTRACTWith advancement of technology things are becoming simpler and easier for us. Automatic systems are being preferred over manual system. The purpose of this project is to design and construct A GSM based home automation using AVR. Using GSM networks, in this project a home power control system has been proposed that will act as an embedded system which can monitor and control appliances and other devices locally using built-in input and output peripherals. The system has a delay of 2 m...
ABSTRACTMetal detectors are electronics sensors that indicate the presence of metallic object without making physical contact with object. They are effective and useful security tools employed in strategic places such as airport, bank, stadiums, government houses and also in production industries to detect presence of metallic object on person luaggages, consignments foods, drugs garments etc. The study present a metal detector comprising a radio frequency oscillator, demodulating unit, trigg...
ABSTRACTMicrocontroller based automate controller is a project design of a system that is used in operating a gate automatically. The system opens the gate automatically when a human being or car is about to enter a compound or exit a compound. The system works by sensing the light rays from the head lamp of the vehicle. The light ray is sensed and signal is used in operating the gate. Different blocks of circuit are put together to ensure that the system works perfectly as desired. The block...
ABSTRACTThis project shows the construction of a microcontroller based security door using smart card. It is aimed towards programming the microcontroller to control the hardware in sliding door. The system consists of a microcontroller 89S52 which sends a signal to the multiplexers on insertion of the smart card in the card slot. The multiplexers consist of ICS which prompts for a display of the identity of the card user in the liquid crystal display (LCD). The LCD displays the status of the...
ABSTRACT An inverter is a system which is capable of converting DC voltage from a battery into AC voltage. The Inverter constructed converts 12V dc to 220V Ac. It consists of an oscillator section using 8V dc to produce 50Hz sine wave. The sine wave is amplified by Tip 41 and used to drive IRPF 250 MOSFET power transistors capable of delivering 500W norminally.The mosfet switches the 12V dc across the high current transformer which then produces the Ac at its output. The output of the trans...
ABSTRACTThe general approach to any design of a process plant involve an advanced network of Chemical Engineering processes. This equipment design project was carried out to design a molten salt cooler (heat exchanger) for production of 2.7 x 104 tonnes/year capacity of phthalic anhydride by direct synthesis of gaseous naphthalene.The information concerning the design of this equipment was gotten from literature review which was then used to obtain the physical properties datas. The mater...
INTRODUCTION A public address system is an electronics sound amplification and distribution system with a microphone, amplifier and loud speaker used to allow a person to address a large public. The public address system consists of three main parts namely, the microphone (input transducer), amplifier and the loudspeaker (output transducer). The microphone picks up the sound and convert it to electronic signal in milivolts and this is fed to the amplifier for amplification. In this project, a...
ABSTRACT As the name of the project implies “Automatic Emergency Light” is an electronic system that can provide light during emergency situations i.e when mains (NEPA) supply fails. This system can provide enough light with full brightness in a given room or office. The system makes use of white light emitting diodes for the lightings. It is automatic in operation, in the sense that it can switch itself off when the battery charges full. Automatic Emergency light comprises three s...
ABSTRACT As the name of the project implies “Power Inverter”, is an electronics system that converts DC Energy (voltage) to an AC energy. The major aim of this project is to design and construct a 1000VA Power inverter that is capable of powering loads of equivalent ratings, in the absence of power supply from NEPA or Generator. The system (power inverter) consists of the AC mains sensor section, Relay/change over section, Battery charger section, oscillator section, Driver section, out...
ABSTRACT This design implementation of this electronic sequential sign post display employs the use of some specialized components. This section of the project introduces the reader to the different section of the project and the components that makes them up.Emphasis are laid on describing the behaviour and operational system of the components as related to the project modeling, analysis, design and implementation of an ELECTRONIC SIGN POST, which is made up of a power supply, a shift regist...