ABSTRACT The construction industry consumes about forty percent of the world’s energy. The high increasing rate of construction activities has led to exploitation of most of the natural resources. These activities have led to massive deforestation and clearing of green cover for settlement and infrastructure development in Kampala. The repercussions of these activities are catastrophic such as poor air quality, urban heat island effect, toxic gas emission, increased cooling costs, which lat...
ABSTRACT In recent years the entire world is a warring about energy resources limitation, specifically Sudan country confronts critical crises in fossil fuel resources and yet more of electricity energy producing from fired thermal power plants. One from these plants Garri”2” combined cycle producing about 180MW. Exergy analysis in the light second law of thermodynamics is powerful tools to investigate from optimization of engineering devices. Exergy analysis has been carried out analytic...
ABSTRACT Robotic is an electromechanical system, help improve production accuracy, and reduces time and increase production. In this project a study of 3D robotic ARM design, simulation concepts and theories for the painting of cars that deals with the design, construction, operation, and application of robots is conducted. The simulation covers different parameters to evaluate the design. Moreover simulation environment help to test these parameters cost effectiveness of building robots and ...
Abstract In the agricultural projects that use the center pivot irrigation system, which depends on the groundwater wells as a source of water using turbine pumps, which are actuated by internal combustion engines, the suspension of the center pivot irrigation device on the movement when a malfunction occurs with its continuous flow of water is a big problem and waste water, fuel and time, It also damages some crops that are heavily affected by water,this research studies the design of an aut...
Abstract Sudanese rural tanning is an inherited craft. The methods and the indigenous materials employed by the rural tanners have remained unchanged for a long time. This is due to poverty, illiteracy, poor communications and lack of access to modern scientific technologies of leather production. As a result, the leathers produced by rural tanners are hard, crusty, liable to crack, tear. Moreover, the process period is long. The objective of the study is to investigate the possibilities of a...
Abstract Three phase induction motors are mostly used in industry for various operations. In this thesis the Variable Frequency Derive control the speed of 3-phase induction motor based on programmable logic controller and supervisory control and data acquisition technology. An implementation of a hardware and software for speed control, direction control, parameter monitoring on supervisory control and data acquisition screen is also provided. tank filling ,bottle filling and capping system ...
ABSTRACT This study was carried out with objectives of developing a proper decision aid for irrigation indenting of multiple crop rotation based on Penman- Montieth equation( 1994) and amenable for the format of meteorological data of the Sudan. Consequently the study developed a mathematical simulation of canal operation for the purpose of optimization of water allocation within such a canal. Linear programming algorithm was made to optimize irrigation water allocation between different outl...
Abstract Abstract -This study aimed to use and attempted to apply total quality management TQM in the Sudanese garment manufacturing factories to improve productivity and profitability and product quality and solving the factory's problems to meet customer satisfaction and decrease the garment imported and determined the potential of competition of local factories in the local and global market. The study designed and employed two methods, one for local garments factories in Sudan and the sec...
TABLE OF CONTENT i االية Dedication ii Acknowledgment iii Abbreviations iv Abstract vi viii الملخص Table of content x List of tables xiii List of figures xiv CHAPTER ONE 1 1.1 Introduction 1 1.2 Study scope 4 1.3 Problem descriptions 4 1.4 Study objectives 5 1.4.1 Main objective 5 1.4.2 Specific objectives 5 CHAPTERTWO 6 2.1 Introduction 6 2.2 Materials and method 9 2.2.1 Field preparation 9 2.2.2 Field Measurements 11 2.3Result and dissection 15 CHAPTER THREE 22 xi 3.1 Introductio...
ABSTRACT The study was to design a sanitary landfill in Kapchorwa central division to curb the problem of improper solid waste disposal. According to the study that was conducted within the municipality; it was found out that the municipality majorly had four main sources at which the solid wastes are generated; Residential wastes, Commercial wastes and Institutional wastes Qualitative data was collected to know the characteristics of solid wastes whereas quantitative data was used to measu...
ABSTRACT In this current situation, the degree of security is feeble. So there is a lot of robbery, theft going on in and around the world. So, people fear to keep any of their valuables in their homes. Henceforth, many people prefer to keep it in banks. However, in this insecure world even banks are not too safe enough to satisfy people needs. A common man/woman feels his/her valuables are secured if there is efficiency in security. Hence this project can give effective security in minimal c...
ABSTRACT The project is designed to automatically supply continuous power to a load through one of the three sources of supply that are: solar, mains and generator or to combine the sources to supply the load all together at the same time. The three socket outlets represent the three sources. The sockets outlets are connected to three step down transformers which reduce the input 230V or 240V to 12Vac. These 12Vac are rectified and regulated to 5Vdc which act as an input to the microcontrolle...
ABSTRACTSolid waste (garbage) is increasingly becoming a big problem in many cities of the world andKansanga Parish in Makindye East Division- Kampala City is no exception. This report is from astudy that looks at the nature, practices, challenges, and possible solutions for garbagemanagement systems at community level in Kansanga Parish, Makindye East division. The studyplaces emphasis on domestic waste. This is because in Kansanga Parish this category generatessubstantial amounts of solid w...
ABSTRACT Rural roads constitute about 65% of the Uganda road network, which provide a critical link in the road transport network, facilitating access to and development of the rural areas. Traffic volume on rural roads in Uganda is very low, 90 % of the rural road network has an Average Annual Daily Traffic (AADT) less than 200, with an average road width of about 5.0 meters. The main problem facing the development of rural roads lies in the method of construction. Common methods used...
ABSTRACT Irrigation is a technology that ensures a good soil-moisture balance resulting into a good environment for crop growth for the well-established irrigation systems This project covered the different sections which included the site visits, desk studies, topographic and geographic studies, nature of the land. The specific objective entailed the determination of pertinent parameters for the design, coming up with the system layout to ensure every farmer gets water and sizing of the pipe...